Compact and light weight, it can be used as an addition to existing systems to enhance audio reproduction in small to medium sized areas. As a standalone unit, the Duecanali 804 DSP+D amplifier platform shines with outstandingly low power consumption and thermal dissipation.
Built in state of the art DSP, in conjunction with Dante, allows flexibility during installation and extensive controllability.
Power supply
Protections
Fully protected circuit design with:
General
Loudspeaker system configuration
Alarms and GPI/O
Digital Signal Processing
Remote management
Remote Control & Monitoring
Number of channels | 2 | |||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Output power | Single channel mode | Distributed line* | Bridge mode | |||||||||||||||||||||
2 Ω | 4 Ω | 8 Ω | 70V | 100V | 4 Ω | 8 Ω | ||||||||||||||||||
500 W | 400 W | 400 W | 400 W | 400 W | 1000W | 800W | ||||||||||||||||||
Max output voltage / current | 80 Vpeak / 39 Apeak | |||||||||||||||||||||||
AC Main Power | ||||||||||||||||||||||||
Power supply | Universal, regulated switch mode with PFC | |||||||||||||||||||||||
Nominal power requirement | 100-240 V ±10%, 50-60 Hz | |||||||||||||||||||||||
Operating voltage | 90 V - 264 V | |||||||||||||||||||||||
Power consuption** | 115 V | 230 V | ||||||||||||||||||||||
Idle | 23.0 W | 0.34 A | 22.5 W | 0.21 A | ||||||||||||||||||||
1/8 of max output power @ 4 Ω | 148 W | 1.4 A | 147 W | 0.9 A | ||||||||||||||||||||
Thermal | ||||||||||||||||||||||||
Operating temperature range | 0° - 45° C - 32° - 113° F | |||||||||||||||||||||||
Thermal dissipation** | 115 V | 230 V | ||||||||||||||||||||||
Idle | 78 BTU/h | 19.7 kcal/h | 77 BTU/h | 19.4 kcal/h | ||||||||||||||||||||
1/8 of max output power @ 4 Ω | 162 BTU/h | 40.8 kcal/h | 161 BTU/h | 40.6 kcal/h | ||||||||||||||||||||
AUDIO | ||||||||||||||||||||||||
|
||||||||||||||||||||||||
Frequency response | 20 Hz - 20 kHz (±0.5 dB) @ 1 W, 8 Ω or (±2.5 dB) @ 32W, 70V lines / 65 W, 100V lines | |||||||||||||||||||||||
S/N ratio | > 106 dB (20 Hz - 20 kHz, A weighted) | |||||||||||||||||||||||
Crosstalk separation | <70 dB @ 1kHz | |||||||||||||||||||||||
THD+N | < 0.1% from 0.1 W to full power (typically <0.05%) | |||||||||||||||||||||||
IMD | < 0.05% from 0.1 W to full power (typically <0.05%) | |||||||||||||||||||||||
Input impedance | 20 kΩ balanced | |||||||||||||||||||||||
Slew rate | >50 V/μs @ 8Ω, input filter bypassed | |||||||||||||||||||||||
Damping factor | > 500 @ 20-100 Hz (Lo-Z) | |||||||||||||||||||||||
DSP | ||||||||||||||||||||||||
AD Converter | 24bit @ 48 kHz Tandem® architecture, 125 dB dynamic range | |||||||||||||||||||||||
DA Converter | 24bit @ 48 kHz Tandem® architecture, 117 dB dynamic range | |||||||||||||||||||||||
Internal precision | 32 bit floating point | |||||||||||||||||||||||
Latency | 2.5 ms fixed latency architecture | |||||||||||||||||||||||
Input equalizer | Raised-cosine, custom FIR, param. IIR: peaking, hi/lo-shelving, all-pass, band-pass, band-stop hi/lo-pass | |||||||||||||||||||||||
Output equalizer | Linear phase (FIR), hybrid (FIR-IIR), Bessel: 6 dB/oct to 48 dB/oct (IIR) | |||||||||||||||||||||||
Crossover | Butterworth, Linkwitz-Riley | |||||||||||||||||||||||
Delay | up to 100 ms per output | |||||||||||||||||||||||
Input EQ | ||||||||||||||||||||||||
Output EQ | ||||||||||||||||||||||||
Limiters | Peak, RMS voltage, RMS current, TruePower™ | |||||||||||||||||||||||
Damping control | Active DampingControl™, LiveImpedance™ measurement | |||||||||||||||||||||||
Front panel | ||||||||||||||||||||||||
Indicators and Controllers | 1 x LED - Status 1 x LED - Over-temperature protection 1 x LED bar - Signal level + CLIP 1 x LED bar - Signal level and over-temperature protection 1 x Knob - Level attenuator (continuous) 1 x Push-button - Setting operating parameters 1 x Push-button - Preset selector 1 x DIP switch - Toggle energy save on/off per channel pair 1 x Power switch - |
|||||||||||||||||||||||
Connectors | ||||||||||||||||||||||||
AC main | 1 x IEC C20 connector - 20 A max (region-specific power cord provided) | |||||||||||||||||||||||
Audio signal input | 2 x 3 pin Phoenix MC 1.5/3-ST-3.81 - Signal input – MAIN | |||||||||||||||||||||||
Alarm | 1 x 12 pin Phoenix MC 1.5/12-ST-3.81 - Alarm connector | |||||||||||||||||||||||
Remote command | 1 x 4 pin Phoenix MC 1.5/4-ST-3.81 - Remote on/off switch and aux voltage | |||||||||||||||||||||||
Network/data | 1 x USB plug - USB connection 1 x Rj45 socket - RS485 data connection (non-DSP version) 1 x Rj45 socket - DANTE® |
|||||||||||||||||||||||
Rear panel | ||||||||||||||||||||||||
Indicators and Controllers | 1 x DIP switch - Toggle lo/hi impedance connection 1 x DIP switch - Toggle 70V/100V distributed line nominal voltage 1 x DIP switch - Toggle High Pass Filter 1 x DIP switch - Toggle 35Hz/70Hz HPF cutting frequency |
|||||||||||||||||||||||
Audio | ||||||||||||||||||||||||
Amplifier | Highly efficient Powersoft Class D circuitry | |||||||||||||||||||||||
Construction | ||||||||||||||||||||||||
Dimensions (L x H x W) | 483 mm x 44.45 mm x 360 mm (19.0 in x 1.8 in x 14.2 in) | |||||||||||||||||||||||
Weight | 7 kg (15.4 lb) |