The X4L has been designed to deliver the output voltage required by the latest generation of high performance loudspeakers.
Powersoft’s legendary power supply is suitable to Single Phase, Bi-Phase or Three Phase operation from 85 VAC up to 460 VAC without need of selection. True Three Phase load balancing is directly achievable without any complex load assignment in the power distribution system. Powersoft X4L provides four fully processable channels and selectable inputs from analog sources as well as digital AES3 and two redundant Dante™* streams.
Channel mixing and routing can be easily performed thanks to the integrated low latency DSP, providing the highest degree of freedom in sound shaping and speaker management. Full support of 100 Mbps and Gigabit Ethernet makes it easy to integrate Powersoft X4L into any existing infrastructure. Completely integrated into ArmoníaPlus™, the Powersoft X4L interface is also available for smartphone and tablet, providing a new experience in power management.
Data de livrare: Sambata, 01.06.2024
* DANTE version only
Number of channels | 4 | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
Output power | Single channel mode | |||||||||
2 Ω | 4 Ω | 8 Ω | ||||||||
8200 W | 6800 W | 4800 W | ||||||||
Max output voltage / current | 300 Vpeak / 140 Apeak | |||||||||
AC Main Power | ||||||||||
Power supply | Universal, regulated switch mode with PFC (Power Factor Correction) | |||||||||
Nominal power requirement | 100-240 V ±10%, 50-60 Hz | |||||||||
Operating voltage | 90 V - 264 V | |||||||||
Thermal | ||||||||||
Operating temperature range | 0° - 45° C - 32° - 113° F | |||||||||
AUDIO | ||||||||||
Frequency response | 20 Hz - 20 kHz (±0.5 dB) @ 1 W, 8 Ω | |||||||||
Noise floor | -70 dBV (20 Hz - 20 kHz, A weighted) | |||||||||
S/N ratio | >100 dB (20 Hz - 20 kHz, A weighted) | |||||||||
Crosstalk separation | >70 dB @ 1kHz | |||||||||
THD+N | <0.05% from 1 W to full power (typically <0.02%) | |||||||||
IMD | <0.05% from 1 W to full power (typically <0.02%) | |||||||||
Input impedance | 10 kΩ balanced | |||||||||
Damping factor | >5000 | |||||||||
DSP | ||||||||||
DSP architecture | ARM Cortex A-8 processor and TI C6000 DSP platform | |||||||||
AD Converter | Dual 24 bit 48 kHz Tandem® architecture with 127 dBA of dynamic range and THD <0.005% (20 Hz - 20 kHz) | |||||||||
DA Converter | Dual 24 bit 48 kHz Tandem® architecture with 122 dBA of dynamic range and THD <0.003% (20 Hz - 20 kHz) | |||||||||
Internal precision | 40 bit floating point | |||||||||
Firmware | Network upgradable firmware | |||||||||
Memory/presets | 1 Gb RAM plus flash memory for 50 Snapshots and more than a hundred* Speaker Presets *exact number depends on the complexity of the specific Speaker Presets / 50 stored locally | |||||||||
Latency | 2.51 ms fixed latency architecture | |||||||||
Input equalizer | Three layers (Asymm. raised cosine) 32 filters each one + group filter | |||||||||
Output equalizer | Per channel: 8+16 fully parametric IIR filters (peaking, hi/lo-shelving, hi/lo-pass, band-pass, band-stop, all-pass), two custom FIR up to 2048 taps @ 48 KHz | |||||||||
Crossover | Butterworth, Linkwitz-Riley, Bessel (normalized to -3 dB) : 6 to 48 dB/oct (IIR), linear phase brick-wall FIR (128 taps, ≥ 400 Hz) | |||||||||
Delay | Up to 150 ms for source alignment; up to 2 s per AdvEQ/Group section; up to 100 ms per output; all with 0.02 ms stepping. | |||||||||
Limiters | RMS voltage, Peak voltage, Clip (instant peak voltage with look-ahead), TruePower™, RMS current | |||||||||
Damping control | Active DampingControl™ | |||||||||
Construction | ||||||||||
Dimensions (L x H x W) | 483.00 mm x 88 mm x mm (19.0 in x 3.5 in x -- in) | |||||||||
Weight | 24 kg (52.9 lb) |